收藏本站
Automatic RF MESFET Amplifier
Drain-Current Controllers
MESFET
FULLY
ON
GATE
VOLTAGE
0V
USER
ENTERED
DAC CODE
FFFh
ADC CODE
READ
FROM
THE FIFO
FFFh
RCS_+ TO
RCS_- SENSE
VOLTAGE
VREFDAC / 4
PGAOUT
VOLTAGE
0V
GATE VOLTAGE
ALARM
THRESHOLDS
DEFAULT
VH = FFFh
TOO HIGH
NEW HIGH GATE
VOLTAGE ALARM
VGATE
THRESHOLD
WITHIN
THRESHOLDS
NEW LOW GATE
VOLTAGE ALARM
THRESHOLD
TOO LOW
OFF
-2 x VREFDAC
000h
000h
0mV
VREFADC
DEFAULT
VL = 000h
Figure 7. DAC Code Range
Connect the MESFET drain to the RCS_- input. Connect
the MESFET’s gate to the GATE_ output. Set the GATE_
voltage to -2 x V REFDAC to turn the MESFET fully off.
Set the GATE_ voltage to 0V to turn the MESFET fully
on. See Figure 7.
The MAX11014/MAX11015 GATE_ output voltage can
be clamped to the external voltage applied at
ACLAMP_. Setting OPSAFE_ high clamps the GATE_
voltage unconditionally. The GATE_ can also be
clamped by different commands issued through the
serial interface. These devices can also monitor the
alarms through the software to modify the clamping
mechanism. See the Automatic GATE Clamping and
ALMHCFG (Read/Write) sections.
12-Bit ADC Description
The MAX11014/MAX11015 ADCs use a fully differential
successive-approximation register (SAR) conversion
technique and on-chip track-and-hold (T/H) circuitry to
convert temperature and voltage signals into 12-bit dig-
ital results. The analog inputs accept single-ended
input signals. Single-ended signals are converted using
a unipolar transfer function. See the ADC Transfer
Function section for more details.
The internal ADC block converts the results of the inter-
nal die temperature, remote diode temperature read-
ings, current-sense voltages, and ADCIN_ voltages.
The ADC block also reads back the GATE_ analog out-
put voltage and converts it to a 12-bit digital result. The
conversion results are written to the FIFO memory. The
FIFO holds up to 15 words (each word of 16 bits) with a
leading 4-bit channel tag to indicate which channel the
12-bit data comes from. See Table 25. The FIFO reads
back data words either one at a time or continuously.
See the ADCCON (Write) section. The FIFO always
stores the most recent conversion results and allows
the oldest data to be overwritten. The FIFO indicates an
overflow condition and underflow condition (read of an
empty FIFO) through the flag register. See the FLAG
(Read) section.
Analog Input Track and Hold
The equivalent circuit of Figure 8 details the
MAX11014/MAX11015’s ADCIN_ input architecture. In
track mode, a positive input capacitor is connected to
ADCIN1/ADCIN2. A negative input capacitor is con-
nected to AGND. After the T/H enters hold mode, the
difference between the sampled input voltages and
AGND is converted. The input-capacitance charging
rate determines the time required for the T/H to acquire
an input signal. The required acquisition time lengthens
with the increase of the input signal’s source imped-
ance. Any source impedance below 300 Ω does not
significantly affect the ADC’s AC performance. A high-
impedance source can be accommodated either by
placing a 1μF capacitor between ADCIN_ and AGND.
The combination of the analog-input source impedance
and the capacitance at the analog input creates an RC
______________________________________________________________________________________
21
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX12000ETB+T IC AMP GPS FRONT 1575MHZ 10TDFN
MAX12005ETM+T IC SATELLITE IF SWITCH 48-TQFN
MAX1385BUTM+ IC RF LDMOS BIAS CNTRLR 48-TQFN
MAX1470EUI+T IC RECEIVER 315MHZ 28-TSSOP
MAX1470EVKIT-315 EVAL KIT FOR MAX1470 315MHZ
MAX1471EVKIT-315 EVAL KIT FOR MAX1471 315MHZ
MAX1472EVKIT-433# EVAL KIT MAX1472
MAX1473EVKIT-433 EVAL KIT MAX1473
相关代理商/技术参数
MAX11014EVKIT+ 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR THE MAX11014 - Bulk
MAX11015 功能描述:射频放大器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel
MAX11015BGTM 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11015BGTM+ 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11017 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX11017ATL+ 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX11017ETL+ 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX11019 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32